Сброс абсорбера Canon PIXMA MP190.

Порядок действий.

Сначала надо войти в сервисный режим:
1 Выключить аппарат (аппарат должен быть подключен к компьютеру по USB)
2 Нажать и удерживать нажатой кнопку Resume обозначенную треугольником в круге.
3 Не отпуская кнопку Resume нажать кнопку ВКЛ (держать обе кнопки нажатыми)
4 Когда загорится индикатор включения - отпустить Resume (ВКЛ держать нажатой) и два раза её нажать, после чего отпустить обе кнопки.
5 Запустить программу.

Наличие установленных драйверов не обязательно.

LED Blinking (SFP)

Error code (MFP)

Error

Message on the LCD

Solution

Ink tanks/Cartridges

4 times

U041

No ink

Ink has run out. Replace the ink tank and close the cover.

Replaced the empty ink tank

CLI-8CMYBk, PGI-5Bk

4 times

U041

No ink

MP170: CHECK INK MP450: Ink has run out.

Replace the empty ink cartridge

PG-40, PG-50, CL-41,

CL-51

4 times

U043

Ink tank not installed

The following ink tank cannot be recognized.

Install the applicable ink tank(s) properly

CLI-8CMYBk, PGI-5Bk, BCI-16

7 times

U071

Multiple ink tanks of the same color installed

Some ink cartridges are not installed.

Multiple ink cartridges of the same color installed.

Verify ink tank and location

CLI-8CMYBk, PGI-5Bk

7 times

U072

Ink tank in wrong position

Some ink cartridges are not installed.

Multiple ink cartridges of the same color installed.

Install ink tank(s) in the correct position

CLI-8CMYBk, PGI-5Bk

7 times

U075

Multiple ink cartridge of the same color installed

Some ink cartridges are not installed.

Multiple ink cartridges of the same color installed.

Verify ink tank and location

PG-40, PG-50, CL-41, CL-51

7 times

U076

Ink cartridge in the wrong position

Some ink cartridges are not installed.

Multiple ink cartridges of the same color installed.

Verify ink tank and location

PG-40, PG-50, CL-41, CL-51

13 times

U130

An ink tank which has once been empty is installed

The remaining level of the following ink cannot be correctly detected.

Press the Stop/Reset button for 5 sec or longer. The error will be cleared and the function to detect the remaining ink amount will be disabled.

CLI-8CMYBk, PGI-5Bk

Note: If the phenomenon occurs in multiple ink tanks at the same time, the above operation will only be effective for the leftmost ink tank.

13 times

U161

Remaining ink amount unknown

MP170: CHECK INK

MP450: The following ink may have run out.

Press the Stop/Reset button for 5 sec or longer. The error will be cleared and the function for detecting the remaining ink amount for the applicable ink cartridge will be disabled.

Note: No ink-related errors will be displayed for that ink cartridge thereafter.

PG-40, PG-50, CL-41,

CL-51

13 times

U162

Remaining ink amount unknown

MP170: CHECK INK

MP450: and ink cartridge that was once empty is installed.

Press the Stop/Reset button for 5 sec or longer. The error will be cleared and the function for detecting the remaining ink amount for the applicable ink cartridge will be disabled.

Note: No ink-related errors will be displayed for that ink cartridge thereafter.

PG-40, PG-50, CL-41, CL-51

14 times

U140

Ink tank not recognized wrong destination

The following ink tank cannot be recognized.

Install the applicable ink tank(s) properly.

PG-40, PG-50, CL-41,

CL-51

15 times

U150

Ink tank hardware

The following ink tank cannot be recognized.

Install the applicable ink tank(s) properly.

CLI-8CMYBk, PGI-5Bk

15 times

U051

Ink cartridge not installed

MP170: CHECK INK

MP450: The following ink cartridge cannot be recognized.

Install the supported ink cartridge(s) properly.

PG-40, PG-50, CL-41,

CL-51

15 times

U140

Ink cartridge not installed

MP170: CHECK INK

Install the supported ink cartridge(s) properly.

PG-40, PG-50, CL-41, CL-51

MP450: The following ink cartridge cannot be recognized.

15 times

U059

Ink cartridge not installed

MP170: CHECK INK

MP450: The following ink cartridge cannot be recognized.

Install the supported ink cartridge(s) properly.

PG-40, PG-50, CL-41,

CL-51

15 times

U052

Ink cartridge not installed

MP170: CHECK INK

MP450: The following ink cartridge cannot be recognized.

Install the supported ink cartridge(s) properly.

PG-40, PG-50, CL-41,

CL-51

15 times

U053

Ink cartridge not installed

MP170: CHECK INK

MP450: The following ink cartridge cannot be recognized.

Install the supported ink cartridge(s) properly.

PG-40, PG-50, CL-41,

CL-51

Error

Service Tool

Service Tool-a

Cause

Check item' Solution

Error code 001

V

n/a

The service function itself is available in the printer, however, the selected item (parameter) is not supported in the printer

Aren't you trying to set the "platen" ink absorber counter though there Is no "platen" ink absorber in the printer?

Is the destination you selected correct?

Error code 002

V

n/a

The service function is not available in the printer

Aren't you trying to set CD-R correction values, though the printer has no CD-R printing functionality?

Aren't you trying to set LF / Eject correction values, though the printer has no LF / Eject correction functionality?

Error code 005

V

The PC does not recognize the printer

Is the cable between the PC and the printer properly connected?

Is the printer power turned on?

Does a distributor connect the PC and the printer?

Error code 006

V

n/a

The printer is not in the service mode.

Is the printer properly in the service mode?

The service tool is not applicable to the printer

Is the printer 2008 or later model? The service tool is not usable in 2007 or earlier models. In 2007 or earlier models, perform the service mode functions via the printer buttons.

Aren't more than one printer connected to the PC?

Error code 007

n/a

The printer is in the factory mode.

The error should not occur in the field, since the error indicates that the shipment setting was not properly performed at the production site.
If the error occurs, contact CINC IJQA Center. The error can be cleared only by CINC IJQA Center.

"Error 122" "Port Name Not Registr"

n/a

V

Too many ports are assigned by OS.

Isn't the Service Tool-a version 3.00 or earlier?
Solution-1 Use the Service Tool-a version 7.00 or later.
Solution-2 Delete the printer icon from the Printer dialog, then set the printer port number to 256 or lower.

The tool freezes.

V

V

No communication with the printer

Is there any error in the printer?